Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - schakal

Pages: [1] 2 3 ... 8
1
Test area / Re: ??o? s??? s?op
« on: 22:49, Wed 11 May 2011 »
lol , WTF !!  :D

2
General Chat / Re: Snow ..
« on: 19:48, Sat 18 December 2010 »
roads yesterday


19 16v



da 9


3
General Chat / Re: Fog Light Replacement
« on: 11:12, Fri 10 December 2010 »
or if you are just doing it for the looks and save weight .
you can .....



 :wink:

4
Renault 5 GT Turbo / Re: Green renault coolant?
« on: 13:41, Sat 22 May 2010 »
gsf sells the green coolant .
you will never be able to clean the header tank as the plastic would
be stained after all those years .
if you are after a brand new one ,i do sell them on ebay .

http://shop.ebay.co.uk/schakal16v/m.htm ... ksid=p3686

5
General Chat / Re: Is it worth paying 25 to join RTOC?
« on: 13:14, Sun 28 February 2010 »
one word !!!

YEPP  :D

6
Do it yourself / droppy doorfix
« on: 18:21, Wed 17 February 2010 »
thought it would be a good idea to do a little report about this
as i am doing it at the moment . please note all techniques used
here are my personal way of doing this and i am by no means a mechanic etc .
the car used in pictures is my renault 9 gtx but as far as i am concerned
its the same in all 5/11/19 and clios (mk1) with torx pins in door hinges.


as far as i understand ,the doors start dropping once the slit bushes and torx pins inside the doors wear over time .
to replace them you have to take the doors out .
i am not going to go too deep into taking doors out .
you simply unscrew the torx pins and pull them out as well
as the check strap pin in the middle of the door .
after unplugging the door loom ,the door comes out .
hardest part is to get them torx pins to budge , on my car 2 of the torx pins were rounded off ,
in the end i had to cut the hinges from the middle
with a very fine cutting disc and weld them back on afterwards .

once the door is out , you are looking at this .
a slit bush at the top of the hinge ,there also is another one at the bottom of the same hinge .
luckily where they are tapped in from top and bottom there is a tiny gap before they meet
which allows you to use something similar to the bit in
the pic to tap them out with a hammer








and the bottom one



all 4 bushes removed from both hinges



and a little clean with some paper dipped in thinners reveal the
crap (best to get some grease in there before fitting new bushes )


i will be fitting my bushes at a later date after the car is sprayed .
but here is a picture of the trial fit (not tapped all the way in )



7
Media / Re: Fake Lottery ticket prank gone wrong !!
« on: 18:09, Fri 23 October 2009 »
dont think its real though  :D

8
Renault 5 GT Turbo /
« on: 10:49, Mon 28 September 2009 »

9
Renault 5 GT Turbo /
« on: 23:57, Mon 13 July 2009 »
Quote from: "r5matt"
Quote from: "dave r5"
heres a hint people,  if you cant see the rust its not a fail

Really ?  :? i find that hard to believe seem as though one of my previous jobs was an MOT'ers assistant!


the question is would you want to drive a car around
with rotten sills ?
i know i dont  8)

10
Renault 5 GT Turbo /
« on: 13:58, Sun 21 June 2009 »
i might have one here mate ,put up a pic of it .
based in barry btw quite local to you .

11
Newbies /
« on: 10:30, Thu 18 June 2009 »
Quote from: "jamlip"
Schakal - the engine is a C-type 1100 with four-speed box.

It mounts into the car differently to a 5, so I have a B14 engine from a Volvo 340 to refit all the GTT bits to. This has the mounts in the right place.

The problem is the gearbox. They're not that great with torque, so if I do a GTT engine, I can't go tuning it!


always wanted to do similar to what you are doing on
a r12 myself .I STILL DO !!!   :P

b14 would be the 1.4 engine i take it ?? a few people i know have fitted
f type renault engines to volvo 340 and 360 series cars using volvo boxes
due to the way engine is mounted(c type renault engines will mate the same boxes ) . this could be the way to go for you .
again i have not looked well into this as yet but you might be
able to use a box from a fuego/18 turbo may be even a 21 turbo to take
the extra torque .

12
Newbies /
« on: 08:26, Tue 16 June 2009 »
welcome mate :)
very interesting project idea you got there .
not so familiar with renault 8 engine setup ,mounting etc . if you put some pictures up might be able to give ideas .

13
General Chat /
« on: 23:22, Wed 10 June 2009 »
have you got a sunroof ?

14
Renault 5 GT Turbo /
« on: 13:10, Sun 03 May 2009 »
Quote from: "itzik"
if you want to send them to my country, i can pay you in paypal.


that aimed at me mate ?  if so pm me i still got the arches  :D

15
Renault 5 GT Turbo /
« on: 10:55, Tue 28 April 2009 »
i got all 4 arches , one of the rears is missing a mounting point but apart from that they look allright and i can do them cheap :)

Pages: [1] 2 3 ... 8